11205-98 Avenue
Grande Prairie, Alberta    1-888-254-6157

Scissor Lift Certification Grande Prairie

Scissor Lift Certification Grande Prairie - Scissor lift platforms are utilized at work locations to be able to allow tradespeople - like for instance masons, iron workers and welders - to reach their work. Utilizing a scissor lift platform is typically secondary to their trade. Hence, it is important that all platform operators be trained properly and certified. Industry, lift manufacturers and regulators all work together to ensure that operators are trained in the safe utilization of work platforms.

Work platforms are likewise referred to as manlifts or AWPs. These machinery are stable and easy to utilize, even though there is always some danger as they raise individuals to heights. The following are various key safety concerns common to AWPs:

To be able to protect those working around work platforms from accidental discharge of power due to close working proximities to power lines and wires, there is a minimum safe approach distance (also referred to as MSAD). Voltage could arc across the air and cause injury to staff on a work platform if MSAD is not observed.

In order to ensure maximum steadiness, caution must be taken when lowering the work platform. When you move the load towards the turntable, the boom must be retracted. This will help maintain steadiness during lowering of the platform.

Rules do not mandate those working on a scissor lift to tie off. However, workers may be needed to tie off if needed by employer rules, job-specific risk assessments or local regulations. The manufacturer-provided anchorage is the only safe anchorage to which harness and lanyard combinations must be attached.

Observe the maximum slope rating and do not go over it. A grade could be measured by laying a board or straight edge on the slope. Next, a carpenter's level could be placed on the straight edge and raised until the end is level. By measuring the distance to the ground and dividing the rise by the straight edge's length, then multiplying by 100, you could determine the percent slope.

A typical walk-around check should be performed to determine if the unit is mechanically safe. A site assessment determines if the work place is safe. This is essential especially on changing construction sites due to the possibility of obstacles, contact with power lines and unimproved surfaces. A function test must be performed. If the unit is used correctly and safely and proper shutdown procedures are followed, the possibilities of accidents are really reduced.

Click to Download the pdf



Forklift Training Courses

  • Forklift Operator Certification Grande Prairie
    Forklift Operator Certification Grande Prairie - Certification for forklifts are needed to ensure the safe utilization of forklifts for those employers in industrial, warehouse or construction environments. The training has to involve a method of ...
    More
  • Skid Steer Ticket Grande Prairie
    Skid Steer Ticket Grande Prairie - On a skid-steer loader, the lift arms are beside the driver along with pivot points behind the driver's shoulders. This makes them different as opposed to a conventional front loader. Due to the operator's ...
    More
  • Order Picker License Grande Prairie
    Order Picker License Grande Prairie - Order preparation operation or order picking as it is more usually known is a method utilized in warehouse operations and consists of staff referred to as order pickers. The order picker's job is to take and ...
    More
  • Telehandler Certification Grande Prairie
    Telehandler Certification Grande Prairie - Telehandler certification programs are both for operators who have some experience driving a typical forklift and for people with no experience. The real-world training provided by these programs ...
    More
  • Skid Steer Loader Training in Grande Prairie
    The engine powered skid-steer loader consists of a small and rigid frame, equipped with lift arms which could attach to numerous industrial attachments and tools in order to perform various labor saving tasks. Typically, skid-steer loaders are ...
    More
  • Crane Training School Grande Prairie
    Crane Training School Grande Prairie - The crane training school offers industry-relevant programs. Courses provide trainees with learning results that match current industry demands. Our small class sizes combine theory and hand-on experience. ...
    More
  • Telehandler License Grande Prairie
    Telehandler License Grande Prairie - The telescopic handler or telehandler is a commonly used machine in agricultural and industrial applications. This equipment is similar in look to a forklift and even works in a similar manner, even though ...
    More
  • Aerial Boom Lift Ticket Grande Prairie
    Aerial Boom Lift Ticket Grande Prairie - Aerial lifts can be utilized to accomplish several unique tasks executed in hard to reach aerial spaces. A few of the odd jobs associated with this kind of lift include performing daily maintenance on ...
    More

Forklift Training Grande Prairie

The huge range of start times and programs we provide should ensure that you come across the perfect match for your needs. Whether you are searching for someone to come train at your place of work or would prefer to train at our facility, we can accommodate all your needs. Our experienced staff can tailor our training to your particular equipment at your site of business.

TOLL FREE: 1-888-254-6157
11205-98 Avenue
Grande Prairie, Alberta    T8V 5A5

www.forklifttraininggrandeprairie.com

Email Us